Home » Steel Grades > Ti Alloy > Ti-6242S Ti Alloy

Category

Contact us

Ti-6242S Ti Alloy

Data Table for: Steel Grades : Ti Alloy : Ti-6242S Ti Alloy

Chemical composition(mass fraction)(wt.%)

Mechanical Properties

  • Quantity
  • Value
  • Unit
  • Young's modulus
  • Tensile strength
  • Elongation
  • Fatigue
  • Yield strength
  • 200000 - 200000
  • 650 - 880
  • 8 - 25
  • 275 - 275
  • 350 - 550
  • MPa
  • MPa
  • %
  • MPa
  • MPa

Physical Properties

  • Quantity
  • Value
  • Unit
  • Thermal expansion
  • Thermal conductivity
  • Specific heat
  • Melting temperature
  • Density
  • Resistivity
  • 10 - 10
  • 25 - 25
  • 460 - 460
  • 1450 - 1510
  • 7700 - 7700
  • 0.55 - 0.55
  • e-6/K
  • W/m.K
  • J/kg.K
  • °C
  • kg/m3
  • Ohm.mm2/m

Heat Treatment:

Annealing

Quenching

Tempering

Normalizing

Q & T

Can produce Ti-6242S Ti Alloy specifications and size

  • Steel grade
  • Specification
  • Processing range(mm)
  • Ti-6242S Ti Alloy
  • Ti-6242S Ti Alloy
  • Ti-6242S Ti Alloy
  • Ti-6242S Ti Alloy
  • Ti-6242S Ti Alloy
  • Ti-6242S Ti Alloy
  • Φ1 to Φ2000
  • 10 to 1000
  • 0.08 to 800(T)*10 to 1500(W)*Long
  • Pipe/tube/slugs/donuts/cubes/other shapes
  • OD: Φ4-410; WT: 1-35 mm
  • THK:0.1mm Width:1500mm

Description

 

Our to produce better steel-based products are the main used in industrial manufacturing various types Ti AlloyTi-6242S plate,Ti-6242S Round Bar,Ti-6242S forgings,Ti-6242S suppliers, Ti-6242S Stock,Ti-6242S sheet, Ti-6242S flat bar, Ti-6242S pipe,Ti-6242S tube,Ti-6242S mould,Ti-6242S round ingot,Ti-6242S cold-rolled steel,Ti-6242S coil,Ti-6242S strap steel,Ti-6242S hot-rolled steel,Ti-6242S medium plate, Ti-6242S heavy plate,Ti-6242S shapped bar,Ti-6242S hexahedral bar,Ti-6242S,Ti-6242S slab ingot,Ti-6242S slab,Ti-6242S price,Ti-6242S square bar,Ti-6242S square steel,Ti-6242S wire.Extending the industrial all kinds of mechanical industrial parts machining and, at the same time, using fine heat treatment process,tempering,hardening,heating,bright annealing,rotary hearth.chemical composition and Improving mechanical properties of Ti-6242S.

 

Ti-6242S Ti Alloy

Our advantages

Ti-6242S properties and heat treatment forged piece, Including Ti-6242S application and specifications, We have all specifications,Including Ti-6242S steel plate, Ti-6242S sheet, Ti-6242S square steel, Ti-6242S flat bar,Ti-6242S round bar,Ti-6242S forgings, we can own production and sales.


Introduction to Our Products:

Specialized high quality steel

We have the advantages of equipment, technologies and price

forged/hot rolling/ extrusion of steel


We can produce the Ti-6242S has the following specifications:

Round bar steel: 1mm to 3000mm

Square-shape steel: 1mm to 2000mm

Plate steel:0.1mm to 2500mm

Width: 10mm to 2500mm

Lenth: We can supply any lenth based on the customer's requirement.

Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes

Tubings: OD: φ6-219 mm, with wall thickness ranging from 1-35 mm.

Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement

Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement

Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.

Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.

We serve you with our honesty, integrity, and professionality.


Chemical composition % of the ladle analysis of grade Ti-6242S and Standards

Titanium Ti-6Al-2Sn-4Zr-2Mo-0.1Si; Duplex Annealed
Categories: Metal; Nonferrous Metal; Titanium Alloy; Alpha/Near Alpha Titanium Alloy

Material Notes: Information provided by Allvac and the references.

Applications: High-temp jet engines. Blades, discs, spacers, seals. High performance automotive valves.


Key Words: Ti-6242Si; Ti-6242S; UNS R54620

 

Physical Properties Metric English Comments
Density 4.54 g/cc 0.164 lb/in³
 
Mechanical Properties Metric English Comments
Hardness, Brinell 318 318 Estimated from Rockwell C.
Hardness, Knoop 346 346 Estimated from Rockwell C.
Hardness, Rockwell C 34 34
Hardness, Vickers 333 333 Estimated from Rockwell C.
Tensile Strength, Ultimate 1110 MPa 161000 psi
Tensile Strength, Yield 1050 MPa 152000 psi
Elongation at Break 13.0 % 13.0 %
Reduction of Area 30.0 % 30.0 %
Modulus of Elasticity 118 GPa 17100 ksi
Compressive Modulus 118 GPa 17100 ksi
Notched Tensile Strength 1025 MPa 148700 psi Kt >17; Average of longitudinal and transverse.
Ultimate Bearing Strength 1800 MPa 261000 psi e/D = 2.0; varies with thickness; this value is at about 2.4 mm.
Bearing Yield Strength 1450 MPa 210000 psi e/D = 2.0
Poissons Ratio 0.325 0.325
Charpy Impact 36.0 J 26.6 ft-lb V-Notch, oxygen content about 0.1%. Value drops with increasing O content.
Fatigue Strength 225 MPa
@# of Cycles 1.00e+7
32600 psi
@# of Cycles 1.00e+7
Kt = 3
  320 MPa
@# of Cycles 50000
46400 psi
@# of Cycles 50000
Kt = 3
  610 MPa
@# of Cycles 1.00e+7
88500 psi
@# of Cycles 1.00e+7
A=0.67
  750 MPa
@# of Cycles 500000
109000 psi
@# of Cycles 500000
A = 0.67
Shear Modulus 44.5 GPa 6450 ksi Calculated
 
Electrical Properties Metric English Comments
Electrical Resistivity 0.000190 ohm-cm 0.000190 ohm-cm
 
Thermal Properties Metric English Comments
CTE, linear 7.70 µm/m-°C
@Temperature 0.000 - 100 °C
4.28 µin/in-°F
@Temperature 32.0 - 212 °F
  7.70 µm/m-°C
@Temperature 205 °C
4.28 µin/in-°F
@Temperature 401 °F
  8.10 µm/m-°C
@Temperature 315 - 540 °C
4.50 µin/in-°F
@Temperature 599 - 1000 °F
average
Specific Heat Capacity 0.460 J/g-°C 0.110 BTU/lb-°F
Thermal Conductivity 7.00 W/m-K 48.6 BTU-in/hr-ft²-°F
Melting Point <= 1705 °C <= 3101 °F Liquidus
Liquidus 1705 °C 3101 °F
Beta Transus 995 °C 1820 °F
 
Component Elements Properties Metric English Comments
Aluminum, Al 5.50 - 6.50 % 5.50 - 6.50 %
Carbon, C <= 0.0500 % <= 0.0500 %
Hydrogen, H <= 0.0150 % <= 0.0150 %
Iron, Fe <= 0.250 % <= 0.250 %
Molybdenum, Mo 1.80 - 2.20 % 1.80 - 2.20 %
Nitrogen, N <= 0.0500 % <= 0.0500 %
Other, each <= 0.100 % <= 0.100 %
Other, total <= 0.300 % <= 0.300 %
Oxygen, O <= 0.150 % <= 0.150 %
Silicon, Si 0.0600 - 0.100 % 0.0600 - 0.100 %
Tin, Sn 1.80 - 2.20 % 1.80 - 2.20 %
Titanium, Ti 83.785 - 87.24 % 83.785 - 87.24 % As Balance; Elemental Compostions per ASTM B265
Zirconium, Zr 3.60 - 4.40 % 3.60 - 4.40 %

 

Users viewing this material also viewed the following:
Titanium Ti-8Al-1Mo-1V (Ti-8-1-1), ST 980°C (1800°F), Aged 595°C
Titanium 11 (Ti-6Al-2Sn-1.5Zr-1Mo-0.35Bi-0.1Si)
Titanium, Ti
Titanium Ti-5Al-2.5Sn (Grade 6)
Titanium Ti-6Al-2Sn-4Zr-2Mo (Ti-6-2-4-2), Duplex Annealed

MTA081 / 14114




Machining performance

Download Ti-6242S the mechanical properties of the report, the report provides detailed performance analysis and application. Download >>


Principal Design Features

One of the most widely used precipitation hardening grades in the business. While soft and ductile in the solution annealed condition, it is capable of high properties with a single precipitation or aging treatment. Characterized by good corrosion resistance, high harness, toughness and strength.


Machinability

Long, gummy chips characterize this alloys machinability. It can be machined in the annealed condition, however condition H1150M will yield best results. Post machining solution treatment of parts will be required prior to final hardening if machining in this condition.


Heat Treatment

CONDITION A--Soak at 1900 F (1038 C) for 30 minutes and cool below 60 F (16 C) for complete martensite transformation. CONDITION H 950- Treat Condition A material at 900 F(482 C) for 1 hour, air cool.. CONDITION H925, H1025, H1075, H1100, H1150- Soak solution treated material for 4 hours at specified temperature, air cool, CONDITION H1150M- Soak solution treated material at 1400 F (760 C) for 2 hours, air cool, then re-heat to 1150 F (620 C) for 4 hours and air cool.


Welding

Successfully welded by common fusion and resistance methods, this alloy should not be joined by oxyacetylene welding. AWS E/ER630 filler metal is recommended if required.


Forging

Soak for 1 hour at 2150 F (1177 C) prior to forging. Do not work below 1850 F (1010 C). Post-work solution treatment is required prior to final hardening.





Hot tags:Ti-6242S steel plate, Ti-6242S sheet, Ti-6242S square steel, Ti-6242S flat bar,Ti-6242S round bar,Ti-6242S forgings

 
 

关闭提示 关闭

 

确 认 取 消

Standard download

More standard download >>

Click the Get Adobe Reader button to download the Adobe Reader:

Download Adobe Reader

Download Adobe Reader

Related steel grade search:Ti-6242S Ti

Previous pageUNS R54620 Ti Alloy
Next page:Ti30Ta Ti Alloy